When a line lets go behind drywall, every minute adds gallons to the damage. Shut the main, then call Water Heater Repairer and a live dispatcher will route you to an independent, licensed and insured plumber near you, plus a water damage contractor if the mess calls for one.
A burst pipe is two jobs at once: stopping the leak and dealing with the water it already dumped. We line up both trades so you are not making five calls while water keeps moving.
Pipe work inside walls touches code, so calls are routed to licensed and insured independent plumbers. Ask to see the license on arrival and check it with your state board.
A spraying line inside a finished wall gets priority over a slow drip under a sink. Arrival is often quick, depending on your location and how many freeze calls are stacked up that night.
You get a written, flat-rate quote for the repair and any wall access before anything gets cut. You know the number before the first tool comes out.
Plenty of the plumbers we route to bring acoustic listening gear and a thermal camera. That narrows the break down to inches instead of tearing out a whole wall to hunt for it.
Split copper, popped PEX fittings, brittle CPVC, and leaks under the slab are all daily calls here. Tell the dispatcher what the pipe looks like and where it runs, and we match you with someone who works on that material every week.
When water has already soaked drywall, insulation, or subfloor, fixing the pipe is only half the job. A drying contractor with moisture meters, air movers, and dehumidifiers can be sent so the cavity dries out before the wall is patched. Closing a wet wall is how small leaks turn into mold calls months later.
Pipe material, location, and the reason it broke decide which repair makes sense.
Pipes running through outside walls, vented crawlspaces, and attics are the first to freeze. Ice expands, pressure builds between the blockage and a closed faucet, and the pipe splits lengthwise, often hours later when it thaws.
Type M copper has a thinner wall than Type L, so it tends to split and pinhole sooner. The fix is cutting back to clean pipe and joining it with a sweated or press fitting.
PEX itself flexes, yet the crimp rings and expansion fittings are where freeze damage shows up. Aging CPVC gets glass-brittle, so a cracked elbow often means nearby joints are close to failing too.
A warm patch on tile or a water meter still moving with everything off usually means the leak is under the slab. Acoustic detection and thermal imaging pin it down, then you weigh a spot repair against a reroute through walls or attic.
Old galvanized pipe corrodes from inside out, and the threads are usually where it gives up. Fixing one joint on a corroded system tends to stress the next weakest point.
Braided supply hoses on toilets, faucets, and washers can rupture at full line pressure with no warning. A water heater relief valve that keeps discharging is a separate warning sign worth a call.
Four steps, and you talk to a person at every one of them.
We walk you through finding the main shutoff and killing power to any wet circuits. Then we ask about the pipe material, the location, and whether any ceiling is sagging.
We route the job to a nearby licensed plumber who carries stock for copper, PEX, and CPVC repairs. If water spread past the leak area, a water damage contractor can be scheduled right behind them.
The pro locates the split, looks over the rest of the line, and notes any pinholes or brittle fittings nearby. A written, flat-rate quote comes before any drywall is cut.
After the repair, the system is repressurized and tested, and joints are checked dry before the wall goes back. Ask about the contractor's own written workmanship warranty before they leave.
A push-to-connect coupling can stop a spraying line in minutes, which makes it a solid emergency patch. Most plumbers treat them as temporary inside a closed wall, and come back to sweat or press a permanent joint once things dry out.
Close the main valve, then call and we will route a local licensed plumber to you.
A pipe in the outside wall of our laundry room froze and split during the first cold snap. I found the main because the dispatcher stayed on the phone with me, and the plumber had the split copper cut out and replaced within a couple hours. He even pointed out that it was thin Type M and why that mattered.
Our water bill doubled and the hallway tile felt warm. They found the hot line leaking under the slab with an acoustic detector and a heat camera. We got two written prices, spot repair or reroute, and he explained both without pushing.
A toilet supply hose upstairs burst and the dining room ceiling started dripping. One call got me a plumber for the line and a separate drying contractor for the ceiling and carpet. Having both lined up from one call saved me a long night of searching.
A tenant in one of my rentals reported a cracked CPVC fitting under the kitchen sink. The plumber replaced it, then showed me two more fittings that crumbled when he touched them. I got a written quote to replace the whole run and time to think it over.
Close the main shutoff right away and kill power to wet areas at the panel. Drain the system by opening a low faucet, pull belongings out of the path, and call for a plumber.
Open the faucet the pipe feeds and warm the section slowly with a hair dryer, heat lamp, or space heater. Never use a torch or open flame, since it can scorch framing or flash steam inside the pipe.
Many are rated for permanent use, but plenty of plumbers treat them as temporary inside a closed wall. Have the plumber explain whether a sweated or press joint is the better long-term choice.
Listening equipment hears the leak, and a thermal camera maps the wet area through the drywall. Together they usually narrow the access hole to a small, patchable opening.
A single leak on newer pipe often makes sense to spot repair through the floor. Repeated leaks or aging copper tend to point toward a reroute so you are not breaking concrete again next year.
Let faucets on outside walls drip on hard freeze nights and open the sink cabinets so warm air reaches the pipes. Heat tape and foam insulation on crawlspace and attic runs help a lot, and the plumber can point out the worst spots.
We route calls to independent plumbers working all over Houma, from older neighborhoods with galvanized lines to newer builds plumbed in PEX. Nearby suburbs are covered too, along with zip codes such as 70363 70360 70361.
In the older parts of Houma, galvanized mains and Type M copper are common, so pinholes and rotted threads are frequent calls. Newer subdivisions are mostly PEX or CPVC, so blown crimp fittings and cracked elbows top the list there. Wherever you are, tell the dispatcher the age of the house and we match the plumber to the pipe.
Frozen crawlspace pipes, attic runs, and slab leaks across older and newer houses.
Leaks that cross into a neighbor's unit, where fast shutoff and documentation both matter.
Surrounding towns around Houma are covered by the same network.
